Aug 27, 2023
Layered MoS2: effective and environment
Scientific Reports volume 13, Article number: 14148 (2023) Cite this article 2 Altmetric Metrics details Photocatalytic degradation is a promising method for removing persistent organic pollutants
Scientific Reports volume 13, Article number: 14148 (2023) Cite this article
2 Altmetric
Metrics details
Photocatalytic degradation is a promising method for removing persistent organic pollutants from water because of its low cost (see solar-driven photocatalysis), high mineralisation of pollutants, and low environmental impact. Photocatalysts based on transition metal dichalcogenides (TMDs) have recently attracting high scientific interest due to their unique electrical, mechanical, and optical properties. A MoS2 photocatalyst of the layered structure was managed to photodegrade methylene blue (MB) under visible light irradiation. The catalyst was thoroughly characterised using SEM, AFM, powder XRD, UV–Vis, Raman, and XPS measurements. The photocatalytic degradation of the MB solution was conducted under the following conditions: (i) reductive and (ii) oxidative. The impact of optical and electronic properties, and the MoS2-MB interaction on photocatalytic activity, was discussed. The apparent rate constants (kapp) of degradation were 3.7 × 10–3; 7.7 × 10–3; 81.7 × 10–3 min−1 for photolysis, oxidative photocatalysis, and reductive photocatalysis. Comparison of the degradation efficiency of MB in reductive and oxidative processes indicates the important role of the reaction with the surface electron. In the oxidation process, oxygen reacts with an electron to form a superoxide anion radical involved in further transformations of the dye, whereas, in the reduction process, the addition of an electron destabilises the chromophore ring and leads to its rupture.
Human activity causes water pollution with chemicals produced during various technological processes. The increasing use of chemicals is due to the current way of life and the continuous growth of the population. This is projected to put more pressure on natural ecosystems and human populations in the near future. Therefore, the development of new wastewater treatment technologies is an important environmental issue. In recent decades, much attention has been devoted to the development of new wastewater treatment methods1. Among them, heterogeneous photocatalysis seems to be very promising, but the most effective catalysts are based on expensive and rare precious metals such as platinum and gold. Recent research2,3 indicates that transition metal dichalcogenides may be a cheap and handy alternative to precious metal catalysts.
Molybdenite (MoS2) scores in the family of transition metal dichalcogenides (TMDs). Molybdenum disulfide is a layered material with sandwich-like structure that reveals many unique properties4. Its features make it possible to use it as a photocatalyst. MoS2 exists in three phases, two stable semiconductor phases with a trigonal prismatic structure (2H and 3R) and a metallic octahedral metastable phase (1T). Bulk MoS2 has an indirect band gap of ~ 1.2 eV, which changes to a direct band gap of ~ 1.9 eV after the reduction of layers5. It indicates that the material has a strong absorption effect on the sunlight. MoS2 nanomaterials provide good catalytic activity due to the high absorption response in the visible wavelength range. The disadvantage of this material is the rapid recombination of photogenerated electron–hole pairs6. Charge separation can be improved by increasing the ratio of the metal edge sites (plain of the edges 100) to the face (basal plane 002). The active centers of the catalyst are mainly concentrated at the edge sites and S vacancies, and its basal plane is considered chemically inert. The edge of the crystal has a high surface energy, which makes MoS2 able to react quickly with oxygen. In addition, single-layer MoS2 has excellent charge carrier mobility, as good as that of carbon nanotubes7.
Considerable efforts have been made to investigate the catalytic activity of various MoS2 nanostructures, such as nanoparticles, mesopores, nanowires, amorphous MoS2, thin films and chemically exfoliated MoS2 layers. MoS2 has been used in environmental engineering for the treatment of organic pollutants by both adsorption and photocatalytic degradation8,9,10,11,12,13,14.
Photocatalytic properties of pristine MoS2 were tested in photocatalytic dyes degradation by several research groups. Lin et al.15 have synthesised monolayered MoS2 nanocrystals (NCs) and S-depleted MoS1.65 NCs. The solar-driven photocatalysis of the MB solution was investigated. The photodegradation of MB without NCs reached about 50% after 440 min, whereas the presence of MoS2 NCs and S-depleted MoS1.65 resulted in complete MB photodegradation after 180 min. and 7 min., respectively. S-depleted NCs also showed excellent photocatalytic efficiency in methyl orange (MO) degradation. It was found that MO was fully degraded within 3 min. The authors not appointed the value of the degradation reaction rate constant. Karmar et al.16 hydrothermally have obtained MoS2 nanoplatelets (MNPs) (S1), a few-layer MoS2 nanosheets (MNSs) (S2) and nanorods (MNRs) (S1#800C). The photocatalytic properties of these materials were evaluated in MB degradation. The obtained reaction rate constants were 8.1 × 10–3 min−1, 5.7 × 10–3 min−1, and 10.0 × 10–3 min−1 for S1, S1#800C, and S2, respectively. Chandhary et al.17 compared photocatalytic performance between bulk MoS2 and nanosheets by degrading MB aqueous solution under sunlight irradiation. The degradation rate constant for MoS2 nanosheets was 27.6 × 10–3 min−1 and for bulk MoS2 3.5 × 10–3 min−1. Lai et al.18 have received highly expanded interlayer spaces MoS2 photocatalyst in the presence of Pluronic F-127 as a template at different pH (1, 3, and 5 denoted as MF-1, MF-3, and MF-5, respectively). MoS2 synthesised without of template, and with template without pH adjusting were assigned as M and MF, respectively. The highly expanded MoS2 exhibited high photocatalytic performance. The photodegradation activity of these materials decreases in order: MF-1 (k = 26.2 × 10–3 min−1) > MF-3 (k = 18.5 × 10–3 min−1) > MF (k = 10.8 × 10–3 min−1) > M (k = 9.4 × 10–3 min−1) > MF-5 (k = 8.2 × 10–3 min−1). Kisala et al. in their recent work19 have produced a layered MoS2 and assessed its photocatalytic properties in the degradation reaction of bromophenol blue (BPB) dye in weakly acidic aqueous solution (pH 5.2) in the presence of t-BuOH and continuous argon flow. The apparent rate constant of the dye decay was 103.7 × 10–3 min−1. The photocatalytic degradation experiment carried out by Kisała et al.19 differed from the other cited works in the conditions of the degradation reaction. In this article, the decomposition of the dye (BPB) occurred as a result of a reaction with an electron. However, in the remaining works, the authors did not specify the reaction conditions (e.g. access to air, which can be presumed) or the pH of the reaction mixture.
Dyes are widely used in different industries, such as textiles, food, rubber, printing, medicine, plastic, concrete, and paper industry. Common use of dyes generates a large amount of hazardous wastewater. The industry that consumes most dyes is the textile industry; one of the most widespread dyes is methylene blue (MB). Methylene blue is a cationic dye that is highly resistant to light, water, chemicals, detergents and microbial activities20.
Our goal was to investigate the MoS2 nanomaterial as a suitable photocatalyst for the degradation of MB under the influence of visible radiation. MB degradation was carried out in two systems: (i) in the presence of oxygen, an oxidative process, and (ii) under argon, in the presence of a hydroxyl radical scavenger, a reductive process. An attempt was also made to determine the MB degradation pathway in an aqueous solution.
Methylene blue (WARCHEM, Warsaw, Poland), t-BuOH (tert-butanol—hydroxyl radical scavenger) and the remaining reagents were of analytical grade and were used as received. The hydrogen ion concentration of the investigated systems was adjusted by NaOH and HCl. MoS2 was synthesised by Kisala et al.19.
The morphology and particle size of the prepared nanoparticles were evaluated by a Helios NanoLab 650 field emission scanning electron microscope (FESEM) (FEI, Hillsboro, Oregon, USA) operating at 5 kV and 18 kV using an ETD detector with secondary electron (SE) imaging mode. Atomic force microscopy (AFM) measurements were performed using a Solver Nano II microscope (NT-MDT Spectrum Instruments LLC, Tempe, Arizona, USA). Phase identification was performed with an X-ray diffractometer (D8 Advance, Bruker, Germany) and 1.5406 Å Cu Kα radiation. The average crystallite size was calculated based on line broadening analysis. The XPS was performed on a KRATOS XSAM800 spectrometer (Kratos Analytical Ltd, Manchester, UK) with an excitation source of A1 Kα (hν = 1486.6 eV). Raman spectra were obtained using an inVia Micro Raman Renishaw spectrometer combined with a Leica DM 2500 M microscope (Renishaw, Wotton-under-Edge, UK) equipped with a 633 nm laser as an excitation source. UV–Vis spectra were recorded using an Agilent Technologies Cary Series UV–Vis-NIR spectrophototometer in the wavelength range of 180–1200 nm. The hydrodynamic diameter of the semiconductor particles and the electrokinetic potential (zeta potential, ζ-potential) were measured by the NanoPlus 3 HD analyser (Particulate Systems, Micromeritics, Norcross, GA 30093, USA).
The MB degradation reaction was performed on MoS2 as a photocatalyst in the Heraeus LRS2 photoreactor (of 250 cm3 volume). For this purpose, 250 cm3 of 5.0 × 10–4 mol dm−3 MB solution containing 0.3 mol dm−3 t-BuOH (only in reductive experiment) and 0.05 g of MoS2 were placed in the photoreactor (mixture pH = 4.6). The resulting mixture was stirred for 30 min in the dark under argon conditions (reductive experiment) or open to air (oxidative experiment). The illumination was carried out using the excimer lamp TQ150 (150 W, with forced water cooling down to 25 °C, of power density 4.7 mW cm−2 measured by digital lux meter Peak Tech 5025, which gives light intensity ca. 7.9 × 1019 photons per second) immersed in the continuously stirred reaction suspension. The photocatalytic reaction was performed up to 120 min illumination time. During the reaction, 2 cm3 samples were collected from the reactor at regular time intervals.
UV–Vis spectra of organic compounds solutions were measured on a VWR UV–VIS 3100 PC spectrophotometer.
Competitive kinetic simulations were performed with the Kinetiscope™ stochastic kinetic simulation software21 freely available on the authors' web page: http://www.hinsberg.net/kinetiscope/. The rate constants of the radical reactions describing the investigated process, required for the competitive kinetics simulation, were taken from the compilation of the rate constants22 and shown in Supplementary Table S1.
Figure 1a,b display the morphology of MoS2 as examined by SEM. The images demonstrate the layered structure of the material, which was beneficial for exposing more edges. The macroscopic view of the material is presented in Fig. 1c. The local morphology of the sample was observed by atomic force microscopy (Fig. 1d). The surface topography observed for MoS2 was rough. This suggests that the sample comprises multiple sheet-like structures, creating layered objects. A water dispersion of MoS2 is depicted in Fig. 1e.
Microscale morphology (SEM) of MoS2 at different places (a,b) macroscale morphology of MoS2 (c), AFM height map (d), water suspension of MoS2 (e).
The XRD spectra (Fig. 2a) of MoS2 showed five distinctive 2H-MoS2 peaks (PDF card #01-071-9809, P63/mmc)23, which can be assigned to the plane (002), (100), (103), (105) and (110) of MoS2 at 2Θ values: 13.95; 33.3; 39.8; 48.2; 59.2, respectively. The crystal structure of 2H-MoS2 is shown in Fig. 2b. Strong intenseness of the peak at 13.95 2Θ reveal that the material has many crystal planes orientated in that direction. The peak broadening indicates a sheet-like crystallite morphology with an average size of 50 nm. Thin-layered MoS2 generally displays n-type behaviour. The XRD results represented that the obtained materials have a pure phase. A more thorough discussion of the XRD measurement results of this material can be found in article Kisala et al.19.
XRD pattern of MoS2 (examined sample—black, reference—red) (a), Crystal structure of 2H-MoS2 (b).
The XPS spectrum was measured to derive the composition of the material. From the XPS spectra (Supplementary Fig. S1), the binding energy values were 162.6 eV for S (2p) and 229.6 eV for Mo (3d)24. Other signals observed may be caused by partial oxidation of the material during the annealing process. The quantitative analysis gave the Mo:S ratio of 1:2.03, corresponding to the stoichiometry of MoS2. The valence band energy was also determined from XPS measurements as 1.6 eV (Fig. 3a). The XPS results confirmed the behaviour of MoS2 semiconductors as n-type.
XPS Valence band energy (a), Raman spectra of MoS2 (b).
The Raman spectrum is like a chemical fingerprint that identifies a molecule or material. In Fig. 3b, one can observe peaks at 378, 404, 451 cm−1, which confirmed the 2H-MoS2 phase25. The peak at 378 cm−1 corresponds to E2g1 and the peak at 404 cm−1 is assigned to Ag1. These results confirm the structure of the 2H-MoS2 catalyst.
The optical properties of MoS2 were analysed by UV–Vis diffuse reflectance spectra (Supplementary Fig. S2). The material absorbed light from the ultraviolet and visible regions, which was attributed to its narrow bad gap. The absorption spectrum of MoS2 reflects the band gap of 2.03 eV, but it also manifests a fine structure with narrow absorption peaks at 1.9 eV (653 nm) and 2.1 eV (590 nm) associated with direct transitions from the spin–orbit split valence band to the conduction bands at the K point in the Brillouin zone.
The absorption of visible light creates consequently holes in the valence band and electrons in the conduction band without affecting essential chemical bonds in the sulphide surface.
The properties of MoS2 in aqueous solution, surface charge, and particle size were analysed. The particle size of MoS2 in water was evaluated by DLS (considering its hydrodynamic radius) where platelet sizes ranged from 72 to 564 nm (Fig. 4a). The zeta potential dictates the sign and amount of surface charge in relation to the surrounding conditions. The ζ-potential of MoS2 was negative in all pH range (2–9) (Fig. 4b). The results showed a decrease of the zeta potential of the particles with an increase of the pH value. The face/edge ratio strongly influences the magnitude of zeta potential; with increasing this ratio, the magnitude decreases19.
The particle size distribution of the H2O dispersion, obtained by DLS (a); zeta potential of 2D-MoS2 as a function of pH (b).
The photocatalytic properties of the MoS2 material were investigated by monitoring the photocatalytic degradation of the MB solution under different conditions: (i) reductive and (ii) oxidative. Figure 5 presents changes in UV–Vis spectra of MB in time.
UV–Vis spectrum changes of MB in time under reductive conditions (a), oxidative conditions (b); irradiation time 0 min—dark blue, 20 min—green, 120 min—orange.
The progress of the degradation reaction was monitored by measuring the changes in MB concentration in specified time intervals. The photocatalytic degradation of MB on MoS2 was performed at pH 4.6. The kinetics of MB degradation follow a pseudo-first-order model Eq. (1):
where kapp is the apparent rate constant; C0 and Ct are the initial concentration and concentration at time t.
A comparison of MB concentration changes in time for photolysis, oxidative photocatalysis, and reductive photocatalysis indicates reductive photocatalysis is the most efficient in MB degradation (Fig. 6a). However, the degradation efficiency calculated from Eq. (2) in both photocatalysis cases is high (97.5%, 80.3% for the reductive and oxidative processes, respectively). The high efficiency of degradation in the oxidative process is mainly caused by processes that take place in the dark period.
where C− 30 is the concentration of MB in time – 30 min; C120 is the concentration of MB in time 120 min.
Disappearance of MB in oxidative photocatalysis (red), reductive photocatalysis (blue), and photolysis (green) (a); molecular orbital energy level diagram for Mo(S)6 in 2H-MoS2 and O2/O2⋅− (b).
The kinetics of MB disappearance represented in Fig. 6a, with an adsorption period in the dark of 30 min, show significant differences between oxidative and reductive processes in the dark period. The MB concentration rapidly decreased in the oxidative process, whereas in the reductive process, one can observe only adsorption on the catalyst surface. We postulate that the decrease of MB concentration in the oxidative process is associated with the presence of oxygen in the reaction mixture. After starting illumination, the reaction enters the slow deceleration stage, in which the concentration of MB slowly decreased. The observed changes are caused by the rapid generation of superoxide radicals in the dark process. The oxygen dissolved in the reaction mixture is adsorbed on the face of MoS2 (the face has a hydrophobic nature) and radicals are generated. The O2⋅− generation rate falls rapidly over time and the reaction slows down. It must be caused by the rapid consumption of oxygen in the reaction mixture. The solubility of oxygen in distilled water is 2.83 × 10–4 mol dm−326.
The electronic structure of MoS2 is determined by the ligand field splitting of the Mo 4d states in the field of the S2− anions since the D6h4 space group of the trigonal layers contains a unique z-axis, the S 3p states subdivide into two groups (pz; px and py), and the Mo 4d into three groups (dz2; dxy and dx2–y2; dxz and dyz) (Fig. 6b). The upper part of the valence band is determined by the d orbitals of Mo (dx2–y2; dxz) and the p orbitals of sulphur (px and py). The band of the antibonding Mo–d–S–p states is located above. The consideration of the 6 Mo valence electrons and a formal charge of − 2 for sulphur give a formal charge of + 4 for Mo in MoS2. The dz2 band is fully occupied, which easily explains the semiconducting behaviour of MoS2. Figure 6b depicts the probable interaction of MoS2 with the oxygen molecule.
The distribution of MB ionic species is presented in Supplementary Fig. S3. The MB solution at pH = 4.6 consists of: [MB]+ = 0.958; [MBH]2+ = 0.04227. Therefore, the main entity that participates in the reactions is the cation [MB]+. The efficiency of catalysis depends on the type of catalyst-substrate interactions. The negative zeta potential of the catalyst suggests the presence of anions in the Stern layer. Methylene blue is a cationic dye that is positively charged under the reaction conditions, hence the driving force of the catalysis is the interaction of a positively charged dye and a negatively charged catalyst surface. It allows the transfer of electrons from the surface substrate to the MB molecule.
Scheme 1 presents classical Lewis formulae, but it should be noted that the formal positive charge of the dye is not placed on the sulphur atom but is distributed over a wide delocalised range outside the thiazine ring. Terminal methyl groups attached to nitrogen atoms bear the most positive charges of the cation28.
Resonance structures of MB cation.
Figure 7a shows the time dependent decomposition of MB dye under light irradiation. A linear dependence was obtained between ln (Ct/C0) and the irradiation time (Fig. 7b), which indicates that reactions follow the pseudo-first-order mechanism. The apparent rate constants (kapp) of degradation were 3.7 × 10–3; 7.7 × 10–3; 81.7 × 10–3; 86.1 × 10–3 min−1 for photolysis, oxidative photocatalysis, reductive photocatalysis, and simulation for reductive photocatalysis. The kapp obtained for simulation is in good agreement with the reductive process.
MB degradation in time in photolysis (violet), oxidative photocatalysis (green), reductive photocatalysis (red), simulations of reductive photocatalysis (light blue) (a); First order linear transforms of MB concentrations changes in time in photolysis (violet), oxidative photocatalysis (green), reductive photocatalysis (red), simulations of reductive photocatalysis (light blue) (b).
The irradiation of MoS2 causes its band-gap excitation and the generation of valence-band holes and conduction-band electrons. The observed loss of dye concentration occurs mainly as a result of the reaction with e– and h+ present on the surface of the catalyst. Continuous blowing of the reaction mixture with argon was used in the reduction process to prevent access to oxygen, and t-BuOH was used as a scavenger of holes, and hydrogen atoms that can be formed in a reductive experiment (Eqs. 3–4)29. Such conditions mean that the mobility of electrons plays a major role in the degradation process. The layered structure of MoS2 favours the separation of charge carriers. The presence of positive and negative charge densities on the Mo-edges and S-faces induces a polarisation effect on these nanoparticles, which effectively separates the electron–hole pair.
Note that a water molecule or hydroxyl anion is not oxidised at the hole to form a hydroxyl radical (⋅OH) because the MoS2 valence band potential (EVB = + 1.6 V) is less positive than the oxidation potential of the hydroxyl ion (E⋅OH/−OH = + 1.9 V), or water molecules (E⋅OH,H+/H2O =+ 2.73 V)30. However, the hole could contribute to MB degradation due to its redox potential (EMB2+/MB+ = + 1.25 V, Fig. 8)31.
Diagram of the electrochemical potentials of the conduction and valence MoS2 bands, and the oxidation31 and reduction33 of MB dye.
As a result of superoxide radical post-reactions, hydroxyl radicals may be formed32:
The Eqs. (6)–(9) may be summarised as Eq. (10). Formed in reaction (9) hydrogen peroxide is the source of hydroxyl radicals (Eq. 11).
The rate of the reaction of O2⋅− with a proton is diffusion controlled and is 5 × 1010 mol−1 s−1. The protonation rate of O2⋅− by proton donors (e.g. MB) is much smaller and depends on the ease of detaching the hydrogen atom from the molecule. Hence, ROS such as O2⋅−, ⋅OH, H2O2, ⋅OOH may take part in the oxidative process.
Based on the simulation, a sequence of reactions was proposed in Scheme 2.
Suggested reductive degradation sequence.
Comparison of MB degradation efficiency in the reduction and oxidation processes indicates the important role of the reaction with the electron. In the oxidation process, oxygen reacts with an electron to form a superoxide anion radical, which is involved in further transformations of the dye. The efficiency of this process is lower than that of the reduction process (Fig. 6a), which suggests that the addition of an electron destabilises the chromophore ring and leads to its rupture.
Regarding the degradation of dyes (especially MB) several articles have been published. Methylene blue is a widely used model compound because of its high water solubility and a convenient way of analysis using UV–Vis spectroscopy measurements. However, few articles on MB degradation on MoS2 nanoparticles contain kinetic data. For comparison with the data we obtained, the works of Sahoo et al.34 seem to be suitable. They studied MB photocatalytic degradation on MoS2 nanosheets of a few layers under visible light. The MoS2 catalyst was prepared by exfoliation in the sonicating bath. The exfoliated MoS2 shows 45.6% degradation efficiency during 1 h. Sahoo et al. in a recent article35 investigated MoS2 nanoflowers and nanosheets. The materials were synthesised using a hydrothermal method. The source of sulphur for nanoflowers was thioacetamide, whereas the source for nanosheets was potassium sulphide. The synthesised MoS2 nanoflowers and nanosheets were used as photocatalysts for the degradation of methylene blue (MB), malachite green (MG) and rhodamine B (RhB) as standard compound under visible light irradiation. The apparent rate constants kapp of the kinetic degradation were 10.27 × 10–3; 7.51 × 10–3; 16.17 × 10–3 min−1 for MoS2 nanoflowers and 7.71 × 10–3; 6.53 × 10–3; 6.05 × 10–3 min−1 for the nanosheet sample in MB, MG and RhB, respectively (Scheme 3).
Suggested oxidative degradation sequence.
The MoS2 studied is a direct band-gap semiconductor and provides new opportunities in photocatalysis. The photocatalytic activity of MoS2 was evaluated for the degradation of the methylene blue dye. MB degradation was carried out in two systems: (i) with air access, oxidative process, and (ii) with a constant flow of argon in the presence of hydroxyl radical scavenger, a reduction process. Such a set of experiments allowed us to show differences in the course of MB degradation depending on the reaction conditions. The process under reducing conditions was found to be more effective than under oxidative conditions, with the total loss of dye concentration 99% and 80% in the reducing and oxidising processes, respectively. The degradation of MB during the dark process in the presence of oxygen was observed for the first time. The course of this reaction suggests a flow of charge between MoS2 and oxygen adsorbed on the surface.
The datasets used and/or analysed during the current study available from the corresponding author on reasonable request.
Rizzo, L. et al. Consolidated vs new advanced treatment methods for the removal of contaminants of emerging concern from urban wastewater. Sci. Total Environ. 655, 986–1008. https://doi.org/10.1016/j.scitotenv.2018.11.265 (2019).
Article ADS CAS PubMed Google Scholar
Chang, K. & Ye, J. Transition metal disulfides as noble-metal-alternative co-catalysts for solar hydrogen production. Adv. Energy. Mater. 6, 1502555. https://doi.org/10.1002/aenm.201502555 (2016).
Article CAS Google Scholar
Fadojutimi, P. O., Gqoba, S. S., Tetana, Z. N. & Moma, J. Transition metal dichalcogenides [MX2] in photocatalytic water splitting. Catalysts 12, 468. https://doi.org/10.3390/catal12050468 (2022).
Article CAS Google Scholar
Hwang, H., Kim, H. & Cho, J. MoS2 nanoplates consisting of disordered graphene-like layers for high lithium battery anode materials. Nano Lett. 11(11), 4826–4830. https://doi.org/10.1021/nl202675f (2011).
Article ADS CAS PubMed Google Scholar
Saha, D. & Kruse, P. Conductive forms of MoS2 and their applications in energy storage and conversion. J. Electrochem. Soc. 167, 126517. https://doi.org/10.1149/1945-7111/abb34b (2020).
Article ADS CAS Google Scholar
Yu, Y. et al. Room-temperature electron-hole liquid in monolayer MoS2. ACS Nano 13, 10351–10358. https://doi.org/10.1021/acsnano.9b04124 (2019).
Article CAS PubMed Google Scholar
Radisavljevic, B., Radenovic, A., Brivio, J., Giacometti, V. & Kis, A. Single-layer MoS2 transistors. Nat. Nano. 6(3), 147–150. https://doi.org/10.1038/nnano.2010.279 (2011).
Article CAS Google Scholar
Wang, C. et al. In-situ synthesis and ultrasound enhanced adsorption properties of MoS2/graphene quantum dot nanocomposite. Chem. Eng. J. 327, 774–782. https://doi.org/10.1016/j.cej.2017.06.163 (2017).
Article CAS Google Scholar
Song, H. J., You, S., Jia, X. H. & Yang, J. MoS2 nanosheets decorated with magnetic Fe3O4 nanoparticles and their ultrafast adsorption for wastewater treatment. Ceram. Int. 41, 13896–13902. https://doi.org/10.1016/j.ceramint.2015.08.023 (2015).
Article CAS Google Scholar
Qiao, X., Hu, F., Hou, D. & Li, D. PEG assisted hydrothermal synthesis of hierarchical MoS2 microspheres with excellent adsorption behaviour. Mater. Lett. 169, 241–245. https://doi.org/10.1016/j.matlet.2016.01.093 (2016).
Article CAS Google Scholar
Gao, Y., Chen, C., Tan, X., Xu, H. & Zhu, K. Polyaniline-modified 3D-flower-like molybdenum disulphide composite for efficient adsorption/photocatalytic reduction of Cr(VI). J. Colloid. Interface Sci. 476, 62–70. https://doi.org/10.1016/j.jcis.2016.05.022 (2016).
Article ADS CAS PubMed Google Scholar
Zhao, Y. et al. The synthesis of hierarchical nanostructured MoS2/graphene composites with enhanced visible-light photo-degradation property. Appl. Surf. Sci. 412, 207–213. https://doi.org/10.1016/j.apsusc.2017.03.181 (2017).
Article ADS CAS Google Scholar
Li, H. et al. Preparation and adsorption capacity of porous MoS2 nanosheets. RSC Adv. 6, 105222–105230. https://doi.org/10.1039/C6RA22414H (2016).
Article ADS CAS Google Scholar
Wu, J. M., Chang, W. E., Chang, Y. T. & Chang, C.-K. Piezo-catalytic effect on the enhancement of the ultra-high degradation activity in the dark by single- and few-layers MoS2 nanoflowers. Adv. Mater. 28, 3718–3725. https://doi.org/10.1002/adma.201505785 (2016).
Article CAS PubMed Google Scholar
Lin, L. et al. A photocatalyst of sulphur depleted monolayered molybdenum sulfide nanocrystals for dye degradation and hydrogen evolution reaction. NanoEnergy 38, 544–552. https://doi.org/10.1016/j.nonoen.2017.06.008 (2017).
Article CAS Google Scholar
Karmar, S., Biswas, S. & Kumbhar, P. A comparison of temperature dependent photoluminescence and photocatalytic properties of different MoS2 nanostructures. Appl. Surf. Sci. 455, 379–391. https://doi.org/10.1016/j.apsusc.2018.05.204 (2018).
Article ADS CAS Google Scholar
Chaudhary, N., Raj, K., Harikumar, A., Mittal, H. & Khanuja, M. Comparative study of photocatalytic activity of hydrothermally synthesized ultra-thin MoS2 nanosheets with bulk MoS2. AIP Conf. Proc. 2276, 020030. https://doi.org/10.1063/5.0025756 (2020).
Article CAS Google Scholar
Lai, M. T. L. et al. The improved photocatalytic activity of highly expanded MoS2 under visible light emitting diodes. Nanoscale Adv. 3, 1106. https://doi.org/10.1039/d0na00936a (2021).
Article ADS CAS PubMed Google Scholar
Kisała, J. et al. Photocatalytic activity of layered MoS2 in the reductive degradation of bromophenol blue. RSC Adv. 12(35), 22465–22475. https://doi.org/10.1039/D2RA03362C (2022).
Article ADS PubMed PubMed Central Google Scholar
Kishor, R. et al. Ecotoxicological and health concerns of persistent coloring pollutants of textile industry wastewater and treatment approaches for environmental safety. J. Environ. Chem. Eng. 9, 105012. https://doi.org/10.1016/j.jece.2020.105012 (2021).
Article CAS Google Scholar
Hinsberg, W., Houle, F. A. KinetiscopeTM a Stochastic Kinetics Simulator. Columbia Hill Technical Consulting, Fremont 2017, California. https://hinsberg.net/kinetiscope/index.html (assessed on 12 Feb 2020).
Buxton, G. V., Greenstock, C. L., Helman, W. P. & Ross, A. B. Critical-review of rate constants for reactions of hydrated electrons, hydrogen-atoms and hydroxyl radicals (•OH/•O-) in aqueous-solution. J. Phys. Chem. Ref. Data 17, 513–886. https://doi.org/10.1063/1.555805 (1988).
Article ADS CAS Google Scholar
Kabekkodu, S. (ed.) PDF-2 2021 (Database), International Centre for Diffraction Data, Newtown Square (PA) (2021).
Ganta, D., Sinha, S. & Haasch, R. T. 2-D material molybdenum disulphide analysed by XPS. Surf. Sci. Spectra 21, 19–27. https://doi.org/10.1116/11.20140401 (2014).
Article ADS CAS Google Scholar
Fan, J.-H. et al. Resonance Raman scattering in bulk 2H-MX2 (M = Mo, W; X = S, Se) and monolayer MoS2. J. Appl. Phys. 115, 053527. https://doi.org/10.1063/1.4862859 (2014).
Article ADS CAS Google Scholar
Carpenter, J. H. New measurements of oxygen solubility in pure and natural water. Limnol. Oceanogr. 11, 264–277. https://doi.org/10.4319/lo.1966.11.2.0264 (1966).
Article ADS CAS Google Scholar
Gutz, I. G. R. pH Calculation and Acid-Base Titration Curves—Freeware for Data Analysis and Simulation. http://www.iq.usp.br/gutz/Curtipot_.html (accessed 6 Apr 2020).
Luger, P., Birger, D., Benecke, L. & Sterzel, H. Charge density studies on methylene blue—A potential anti-Alzheimer agent. Z. Naturforsch. 73(2), 99–108. https://doi.org/10.1515/znb-2017-0165 (2018).
Article CAS Google Scholar
Schneider, J. T., Firak, D. S., Ribeiro, R. R. & Peralta-Zamora, P. Use of scavenger agents in heterogenous photocatalysis: truths, half-truths, and misinterpretations. Phys. Chem. Chem. Phys. 22, 15723–15733. https://doi.org/10.1039/D0CP02411B (2020).
Article CAS PubMed Google Scholar
Wardman, P. Reduction potentials of one-electron couples involving free radicals in aqueous solution. J. Phys. Chem. Ref. Data 18, 1637–1755. https://doi.org/10.1063/1.555843 (1989).
Article ADS CAS Google Scholar
Kishore, K., Guha, S. N., Mahadevan, J., Moorthy, P. N. & Mittal, J. P. Redox reactions of methylene blue: A pulse radiolysis study. Radiat. Phys. Chem. 34(4), 721–727. https://doi.org/10.1016/1359-0197(89)90084-2 (1989).
Article ADS Google Scholar
Hart, E. J., Fielden, E. M. Submicromolar analysis of hydrated electron scavengers. In Solvated Electron (ed. Hart, E. J.) 254–262 (American Chemical Society, 1965).
Ju, H., Zhou, J., Cai, C. & Chen, H. The electrochemical behavior of methylene blue at microcylinder carbon fiber electrode. Electroanalysis 7, 1165–1170. https://doi.org/10.1002/elan.1140071213 (1995).
Article CAS Google Scholar
Sahoo, D. et al. Cost effective liquid phase exfoliation of MoS2 nanosheets and photocatalytic activity for wastewater treatment enforced by visible light. Sci. Rep. 10, 10759. https://doi.org/10.1038/s41598-020-67683-2 (2020).
Article ADS CAS PubMed PubMed Central Google Scholar
Sahoo, D., Shakya, J., Ali, N., Yoo, W. J. & Kaviraj, B. Edge rich ultrathin layered MoS2 nanostructures for superior visible light photocatalytic activity. Langmuir 38, 1578–1588. https://doi.org/10.1021/acs.langmuir.1c03013 (2022).
Article CAS PubMed Google Scholar
Download references
Institute of Biology, University of Rzeszow, Pigonia 1 Str., 35-310, Rzeszow, Poland
Joanna Kisała
Institute of Materials Science, College of Natural Sciences, University of Rzeszow, Pigonia 1 Str., 35-959, Rzeszow, Poland
Renata Wojnarowska-Nowak
Centre for Microelectronics and Nanotechnology, Institute of Physics, University of Rzeszow, Pigonia 1, 35-959, Rzeszow, Poland
Yaroslav Bobitski
You can also search for this author in PubMed Google Scholar
You can also search for this author in PubMed Google Scholar
You can also search for this author in PubMed Google Scholar
J.K.—conceptualisation, methodology, investigation, formal analysis, project administration, writing—original draft, writing—review and editing.; R.W.-N.—the materials characterisation, formal analysis, Y.B.—formal analysis, writing—review and editing. All authors read and approved the final manuscript.
Correspondence to Joanna Kisała.
The authors declare no competing interests.
Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.
Open Access This article is licensed under a Creative Commons Attribution 4.0 International License, which permits use, sharing, adaptation, distribution and reproduction in any medium or format, as long as you give appropriate credit to the original author(s) and the source, provide a link to the Creative Commons licence, and indicate if changes were made. The images or other third party material in this article are included in the article's Creative Commons licence, unless indicated otherwise in a credit line to the material. If material is not included in the article's Creative Commons licence and your intended use is not permitted by statutory regulation or exceeds the permitted use, you will need to obtain permission directly from the copyright holder. To view a copy of this licence, visit http://creativecommons.org/licenses/by/4.0/.
Reprints and Permissions
Kisała, J., Wojnarowska-Nowak, R. & Bobitski, Y. Layered MoS2: effective and environment-friendly nanomaterial for photocatalytic degradation of methylene blue. Sci Rep 13, 14148 (2023). https://doi.org/10.1038/s41598-023-41279-y
Download citation
Received: 31 March 2023
Accepted: 24 August 2023
Published: 29 August 2023
DOI: https://doi.org/10.1038/s41598-023-41279-y
Anyone you share the following link with will be able to read this content:
Sorry, a shareable link is not currently available for this article.
Provided by the Springer Nature SharedIt content-sharing initiative
By submitting a comment you agree to abide by our Terms and Community Guidelines. If you find something abusive or that does not comply with our terms or guidelines please flag it as inappropriate.